View MVTM36BH030M025A00_8386072.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

vtm ? current multiplier rev 1.3 vicorpower.com page 1 of 31 07/2015 800 927.9474 s nrtl cus vtm ? current multiplier high efficiency, sine amplitude converter? (sac?) mil-cots mvtm36 series features ? family of mil-cots current multipliers covering output voltages from 1 to 50 vdc n operating from mil-cots prm ? modules ? high efficiency reduces system power consumption ? high density provides isolated regulated system and saves space ? vi chip ? package enables surface mount or through hole, low impedance interconnect to system board ? contains built-in protection features against: n overvoltage n overcurrent n short circuit n overtemperature ? zvs/zcs resonant sine amplitude converter topology ? less than 50oc temperature rise at full load in typical applications typical applications ? land/air/sea unmanned vehicles/drones ? scanning equipment ? radar ? mobile weapons ? hybrid vehicles product description the vi chip? current multiplier is a high efficiency sine amplitude converter? (sac?) operating from a 26 to 50 vdc primary bus to deliver an isolated output. the sine amplitude converter offers a low ac impedance beyond the bandwidth of most downstream regulators, which means that capacitance normally at the load can be located at the input to the sine amplitude converter. this allows for a reduction in point of load capacitance of typically >100x which results in a saving of board area, materials and total system cost. the vtm current multiplier is provided in a vi chip package compatible with standard pick-and-place and surface mount assembly processes. the co-molded vi chip package provides enhanced thermal management due to large thermal interface area and superior thermal conductivity. with high conversion efficiency the vtm current multiplier increases overall system efficiency and lowers operating costs compared to conventional approaches. the vtm current multiplier enables the utilization of factorized power architecture providing efficiency and size bene?ts by lowering conversion and distribution losses and promoting high density point of load conversion. product ratings v in = 26.0 v to 50.0 v p out = up to 150 w v out = 1.0 v to 50.0 v (various models) i out = up to 80 a
vtm ? current multiplier rev 1.3 vicorpower.com page 2 of 31 07/2015 800 927.9474 mvtm36 series typical application using the mil-cots prm, the output of the vtm is regulated over the load current range with only a single interconnect between the prm and vtm and without the need for isolation in the feedback path. prm al sc os cd vc vh +in ?n +out ?ut sgnd 1 sgnd gnd f 1 c in v in 16 v to 50 v l f 1 c f 1 vc tm pc v out +in ?n ?ut +out isolation boundry vtm primary secondary vtm start up pulse and temperature feedback vf: 26 v to 50 v pc pr il tm sgnd rsc csc ros 10k rvc r df rcd 0.01? sec_gnd
vtm ? current multiplier rev 1.3 vicorpower.com page 3 of 31 07/2015 800 927.9474 mvtm36 series 1 2 3 4 a b c d e a b c d tm vc +in -in +out -out top view full vic smd +out -out pc pin configuration (full) pin number signal name type function a1, a2 +in input power positive input power terminal b1, b2 tm output provides voltage proportional to internal vtm controller temperature. ?power good? flag. c1, c2 vc input connect to 12 v source to power internal vtm control circuits. d1, d2 pc bidir enables power supply when allowed to float high. 5 v during normal operation. e1, e2 -in input power return negative input power terminal a?3, a?4, c?3, c?4 +out output power positive output power terminal b?3, b?4, d?3, d?4 -out output power return positive output power terminal pin description (full)
vtm ? current multiplier rev 1.3 vicorpower.com page 4 of 31 07/2015 800 927.9474 mvtm36 series half vic 1 2 3 4 b c d e f a b e im +in -in +out -out top view a vc tm pc pin configuration (half) pin number signal name type function a1, a2 +in input power positive input power terminal b1 im output provides voltage proportional to load current. c2 tm output provides voltage proportional to internal vtm controller temperature. ?power good? flag. d1 vc input connect to 12 v source to power internal vtm control circuits. e2 pc bidir enables power supply when allowed to float high. 5 v during normal operation. f1, f2 -in input power return negative input power terminal a?3, a?4 +out output power positive output power terminal b?3, b?4 -out output power return positive output power terminal pin description (half)
vtm ? current multiplier rev 1.3 vicorpower.com page 5 of 31 07/2015 800 927.9474 mvtm36 series part ordering information device input voltage range package type output voltage x 10 temperature grade output current revision version vtm 36b f 015 m 080 a 00 vtm = vtm 36b = 26.0 to 50.0 v f = full vic smd t = full vic through hole h = half vic smd 015 = 1.5 v m = -55 to 125c 080 = 80 a a 00 = standard standard models all products shipped in jedec standard high profile (0.400? thick) trays (jedec publication 95, design guide 4.10). part number package size v in k v out temperature current mvtm36bf015m080a00 full vic smd 26.0 v to 50.0 v 1/24 1.50 v (1.08 v to 2.08 v) -55 to 125c 80 a mvtm36bt015m080a00 full vic th mvtm36bf022m055a00 full vic smd 26.0 v to 50.0 v 1/16 2.25 v (1.63 v to 3.13 v) -55 to 125c 55 a mvtm36bt022m055a00 full vic th mvtm36bf030m040b00 full vic smd 26.0 v to 50.0 v 1/12 3.00 v (2.17 v to 4.17 v) -55 to 125c 40 a mvtm36bt030m040b00 full vic th mvtm36bf045m027a00 full vic smd 26.0 v to 50.0 v 1/8 4.50 v (3.25 v to 6.25 v) -55 to 125c 27 a mvtm36bt045m027a00 full vic th mvtm36bf060m020a00 full vic smd 26.0 v to 50.0 v 1/6 6.00 v (4.33 v to 8.33 v) -55 to 125c 20 a mvtm36bt060m020a00 full vic th mvtm36bf072m017a00 full vic smd 26.0 v to 50.0 v 1/5 7.20 v (5.20 v to 10.0 v) -55 to 125c 17 a mvtm36bt072m017a00 full vic th mvtm36bf090m013a00 full vic smd 26.0 v to 50.0 v 1/4 9.00 v (6.50 v to 12.5 v) -55 to 125c 13 a mvtm36bt090m013a00 full vic th mvtm36bf120m010a00 full vic smd 26.0 v to 50.0 v 1/3 12.0 v (8.67 v to 16.7 v) -55 to 125c 10 a mvtm36bt120m010a00 full vic th mvtm36bf180m007a00 full vic smd 26.0 v to 50.0 v 1/2 18.0 v (13.0 v to 25.0 v) -55 to 125c 7 a mvtm36bt180m007a00 full vic th mvtm36bf240m005a00 full vic smd 26.0 v to 50.0 v 2/3 24.0 v (17.3 v to 33.3 v) -55 to 125c 5 a mvtm36bt240m005a00 full vic th mvtm36bf360m003a00 full vic smd 26.0 v to 50.0 v 1 36.0 v (26.0 v to 50.0 v) -55 to 125c 3 a mvtm36bt360m003a00 full vic th MVTM36BH030M025A00 half vic smd 26.0 v to 50.0 v 1/12 3.00 v (1.63 v to 3.13 v) -55 to 125c 25 a mvtm36bh045m020a00 half vic smd 26.0 v to 50.0 v 1/8 4.50 v (3.25 v to 6.25 v) -55 to 125c 20 a mvtm36bh090m010a00 half vic smd 26.0 v to 50.0 v 1/4 9.00 v (6.50 v to 12.5 v) -55 to 125c 10 a
general electrical characteristics specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. vtm ? current multiplier rev 1.3 vicorpower.com page 6 of 31 07/2015 800 927.9474 mvtm36 series absolute maximum ratings the absolute maximum ratings below are stress ratings only. operation at or beyond these maximum ratings can cause permanent da mage to the device. parameter comments min max unit +in to -in -1.0 60 v dc pc to -in -0.3 20 v dc tm to -in -0.3 7 v dc vc to -in -0.3 20 v dc im to -in half chip only 0 3.15 v dc +in / -in to +out / -out (hipot) 2250 v dc attribute symbol conditions / notes min ty p max unit input voltage range v in no external vc applied 26 50 v dc vc applied 0 50 v in slew rate dv in /dt 1 v/s output voltage ripple v out_pp c out = 0 f, i out = full load, v in = 48 v, 20 mhz bw 5 % v out protection overvoltage lockout v in_ovlo+ module latched shutdown 52.0 56.0 58.5 v overvoltage lockout response time constant t ovlo effective internal rc filter 8 s output overcurent trip i ocp 120 % i out_avg short circuit protection trip current i scp 150 % i out_avg output overcurrent response time constant t ocp effective internal rc filter (integrative) 3.8 ms short cicuit protection response time t scp from detection to cessation of switching (instantaneous) 1 s thermal shutdown setpoint t j_otp 125 130 135 c reverse inrush current protection reverse inrush protection disabled for this product
vtm ? current multiplier rev 1.3 vicorpower.com page 7 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bf015m080a00 no load power dissipation p nl v in = 26 v to 50 v 7.5 w transfer ratio k k = v out / v in , i out = 0 a 1/24 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 80 a output current (peak) i out_pk t peak < 10 ms, i out_avg 80 a 120 a efficiency (ambient) h amb v in = 36 v, i out = 80 a 90.0 91.3 % v in = 26 v to 50 v, i out = 80 a 87.3 output resistance (cold) r out_cold t c = -40c, i out = 80 a 0.40 0.76 1.0 m output resistance (ambient) r out_amb t c = 25c, i out = 80 a 0.55 0.98 1.4 m output resistance (hot) r out_hot t c = 100c, i out = 80 a 0.65 1.18 1.5 m switching frequency f sw 1.50 1.60 1.70 mhz output ripple frequency f sw_rp 3.00 3.20 3.40 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 5.0 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 6.7 mhrs vc internal resistor r vc-int 2 k mvtm36bf022m055a00 no load power dissipation p nl v in = 26 v to 50 v 8.6 w transfer ratio k k = v out / v in , i out = 0 a 1/16 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 55 a output current (peak) i out_pk t peak < 10 ms, i out_avg 55 a 82 a efficiency (ambient) h amb v in = 36 v, i out = 55 a 92.6 93.7 % v in = 26 v to 50 v, i out = 55 a 88.8 output resistance (cold) r out_cold t c = -40c, i out = 55 a 0.6 1.1 1.8 m output resistance (ambient) r out_amb t c = 25c, i out = 55 a 0.8 1.4 1.9 m output resistance (hot) r out_hot t c = 100c, i out = 55 a 1.0 1.7 2.2 m switching frequency f sw 1.36 1.43 1.50 mhz output ripple frequency f sw_rp 2.72 2.86 3.00 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 1.9 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 6.0 mhrs vc internal resistor r vc-int 1.0 k
vtm ? current multiplier rev 1.3 vicorpower.com page 8 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bf030m040b00 no load power dissipation p nl v in = 26 v to 50 v 12.0 w transfer ratio k k = v out / v in , i out = 0 a 1/12 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 40 a output current (peak) i out_pk t peak < 10 ms, i out_avg 40 a 60 a efficiency (ambient) h amb v in = 36 v, i out = 40 a 92.5 94.0 % v in = 26 v to 50 v, i out = 40 a 90.2 output resistance (cold) r out_cold t c = -40c, i out = 40 a 1.0 1.6 2.3 m output resistance (ambient) r out_amb t c = 25c, i out = 40 a 1.5 2.2 3.0 m output resistance (hot) r out_hot t c = 100c, i out = 40 a 2.0 2.6 3.3 m switching frequency f sw 1.36 1.43 1.50 mhz output ripple frequency f sw_rp 2.72 2.86 3.00 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 3.8 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 9.5 mhrs vc internal resistor r vc-int 1.0 k mvtm36bf045m027a00 no load power dissipation p nl v in = 26 v to 50 v 7.0 w transfer ratio k k = v out / v in , i out = 0 a 1/8 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 27 a output current (peak) i out_pk t peak < 10 ms, i out_avg 27 a 40 a efficiency (ambient) h amb v in = 36 v, i out = 27 a 93.0 94.7 % v in = 26 v to 55 v, i out = 27 a 89.3 output resistance (cold) r out_cold t c = -40c, i out = 27 a 2.5 4.6 5.9 m output resistance (ambient) r out_amb t c = 25c, i out = 27 a 3.8 6.0 7.8 m output resistance (hot) r out_hot t c = 100c, i out = 27 a 4.5 7.1 9.0 m switching frequency f sw 1.10 1.21 1.30 mhz output ripple frequency f sw_rp 2.20 2.42 2.60 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 3.8 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 9.5 mhrs vc internal resistor r vc-int 1.0 k
vtm ? current multiplier rev 1.3 vicorpower.com page 9 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bf060m020a00 no load power dissipation p nl v in = 26 v to 50 v 14.0 w transfer ratio k k = v out / v in , i out = 0 a 1/6 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 20 a output current (peak) i out_pk t peak < 10 ms, i out_avg 20 a 30 a efficiency (ambient) h amb v in = 36 v, i out = 20 a 94.6 95.5 % v in = 26 v to 50 v, i out = 20 a 92.0 output resistance (cold) r out_cold t c = -40c, i out = 20 a 3.0 7.0 9.0 m output resistance (ambient) r out_amb t c = 25c, i out = 20 a 5.0 8.0 10.0 m output resistance (hot) r out_hot t c = 100c, i out = 20 a 6.0 12.0 15.0 m switching frequency f sw 1.47 1.52 1.57 mhz output ripple frequency f sw_rp 7.94 3.04 3.14 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 4.3 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 9.5 mhrs vc internal resistor r vc-int 0.56 k mvtm36bf072m017a00 no load power dissipation p nl v in = 26 v to 50 v 14.0 w transfer ratio k k = v out / v in , i out = 0 a 1/5 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 17 a output current (peak) i out_pk t peak < 10 ms, i out_avg 17 a 25 a efficiency (ambient) h amb v in = 36 v, i out = 17 a 95.3 95.9 % v in = 26 v to 55 v, i out = 17 a 92.0 output resistance (cold) r out_cold t c = -40c, i out = 17 a 3.3 5.6 7.8 m output resistance (ambient) r out_amb t c = 25c, i out = 17 a 5.0 7.8 10.0 m output resistance (hot) r out_hot t c = 100c, i out = 17 a 7.0 9.1 12.0 m switching frequency f sw 1.50 1.55 1.60 mhz output ripple frequency f sw_rp 3.00 3.10 3.20 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 3.5 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 5.5 mhrs vc internal resistor r vc-int 0.56 k
vtm ? current multiplier rev 1.3 vicorpower.com page 10 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bf090m013a00 no load power dissipation p nl v in = 26 v to 50 v 14.0 w transfer ratio k k = v out / v in , i out = 0 a 1/4 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 13 a output current (peak) i out_pk t peak < 10 ms, i out_avg 13 a 19 a efficiency (ambient) h amb v in = 36 v, i out = 13 a 93.8 95.3 % v in = 26 v to 50 v, i out = 13 a 93.5 output resistance (cold) r out_cold t c = -40c, i out = 13 a 2.0 5.5 9.5 m output resistance (ambient) r out_amb t c = 25c, i out = 13 a 3.9 8.9 13.4 m output resistance (hot) r out_hot t c = 100c, i out = 13 a 5.0 10.6 15.9 m switching frequency f sw 1.85 1.95 2.05 mhz output ripple frequency f sw_rp 3.70 3.90 4.10 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 1.8 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 7.3 mhrs vc internal resistor r vc-int 0.51 k mvtm36bf120m010a00 no load power dissipation p nl v in = 26 v to 50 v 10.5 w transfer ratio k k = v out / v in , i out = 0 a 1/3 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 10 a output current (peak) i out_pk t peak < 10 ms, i out_avg 10 a 15 a efficiency (ambient) h amb v in = 36 v, i out = 10 a 94.2 94.9 % v in = 26 v to 50 v, i out = 10 a 90.0 output resistance (cold) r out_cold t c = -40c, i out = 10 a 12.8 19.7 26.5 m output resistance (ambient) r out_amb t c = 25c, i out = 10 a 20.4 26.5 32.6 m output resistance (hot) r out_hot t c = 100c, i out = 10 a 23.1 29.2 35.2 m switching frequency f sw 1.56 1.65 1.74 mhz output ripple frequency f sw_rp 3.12 3.30 3.48 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 3.8 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 5.6 mhrs vc internal resistor r vc-int 2.0 k
vtm ? current multiplier rev 1.3 vicorpower.com page 11 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bf180m007a00 no load power dissipation p nl v in = 26 v to 50 v 13.5 w transfer ratio k k = v out / v in , i out = 0 a 1/2 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 7 a output current (peak) i out_pk t peak < 10 ms, i out_avg 7 a 10 a efficiency (ambient) h amb v in = 36 v, i out = 7 a 93.0 94.0 % v in = 26 v to 50 v, i out = 7 a 92.0 output resistance (cold) r out_cold t c = -40c, i out = 7 a 19.7 40.0 60.7 m output resistance (ambient) r out_amb t c = 25c, i out = 7 a 30.0 55.0 75.0 m output resistance (hot) r out_hot t c = 100c, i out = 7 a 35.0 60.0 90.0 m switching frequency f sw 1.68 1.77 1.86 mhz output ripple frequency f sw_rp 3.36 3.54 3.72 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 3.8 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 5.7 mhrs vc internal resistor r vc-int 0.51 k mvtm36bf240m005a00 no load power dissipation p nl v in = 26 v to 50 v 8.5 w transfer ratio k k = v out / v in , i out = 0 a 2/3 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 5 a output current (peak) i out_pk t peak < 10 ms, i out_avg 5 a 7.5 a efficiency (ambient) h amb v in = 36 v, i out = 5 a 93.5 96.0 % v in = 26 v to 50 v, i out = 5 a 93.0 output resistance (cold) r out_cold t c = -40c, i out = 5 a 40.0 51.4 70.0 m output resistance (ambient) r out_amb t c = 25c, i out = 5 a 64.0 86.0 120.0 m output resistance (hot) r out_hot t c = 100c, i out = 5 a 85.0 102.0 135 m switching frequency f sw 1.57 1.60 1.63 mhz output ripple frequency f sw_rp 3.14 3.20 3.26 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 3.8 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 5.6 mhrs vc internal resistor r vc-int 2.0 k
vtm ? current multiplier rev 1.3 vicorpower.com page 12 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bf360m003a00 no load power dissipation p nl v in = 26 v to 50 v 9.0 w transfer ratio k k = v out / v in , i out = 0 a 1 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 3 a output current (peak) i out_pk t peak < 10 ms, i out_avg 3 a 4.5 a efficiency (ambient) h amb v in = 36 v, i out = 3 a 95.3 96.0 % v in = 26 v to 50 v, i out = 3 a 93.3 output resistance (cold) r out_cold t c = -40c, i out = 3 a 55.0 108.0 175.0 m output resistance (ambient) r out_amb t c = 25c, i out = 3 a 120.0 158.0 200.0 m output resistance (hot) r out_hot t c = 100c, i out = 3 a 175.0 205.0 235.0 m switching frequency f sw 1.64 1.67 1.70 mhz output ripple frequency f sw_rp 3.28 3.34 3.40 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 3.8 mhrs telcordia issue 2 - method 1 case 1; ground benign, controlled 5.6 mhrs vc internal resistor r vc-int 2.0 k
vtm ? current multiplier rev 1.3 vicorpower.com page 13 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit MVTM36BH030M025A00 no load power dissipation p nl v in = 26 v to 50 v 5.0 w transfer ratio k k = v out / v in , i out = 0 a 1/12 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 25.0 a output current (peak) i out_pk t peak < 10 ms, i out_avg 25 a 37.5 a efficiency (ambient) h amb v in = 36 v, i out = 25 a 88.5 90.8 % v in = 26 v to 50 v, i out = 25 a 85.5 output resistance (cold) r out_cold t c = -40c, i out = 25 a 2.0 5.3 8.5 m output resistance (ambient) r out_amb t c = 25c, i out = 25 a 4.5 7.3 10.0 m output resistance (hot) r out_hot t c = 100c, i out = 25 a 5.0 8.0 12.0 m switching frequency f sw 1.50 1.65 1.80 mhz output ripple frequency f sw_rp 3.00 3.30 3.60 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 4.5 mhrs vc internal resistor r vc-int 8.87 k current monitor: im ? the im pin provides a dc analog voltage proportional to the output current of the vtm. signal type state attribute symbol conditions / notes min typ max unit analog input steady im voltage (no load) v im_nl t c = 25oc, v in = 42 v, i out = 0 a 0.30 0.32 0.38 v im voltage (50%) v im_50% t c = 25oc, v in = 42 v, i out = 12.5 a 0.94 v im voltage (full load) v im_fl t c = 25oc, v in = 42 v, i out = 25 a 1.80 v im gain a im t c = 25oc, v in = 42 v, i out > 12.5 a 69 mv/a im resistance (external) r im_ext 2.5 m
vtm ? current multiplier rev 1.3 vicorpower.com page 14 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bh045m020a00 no load power dissipation p nl v in = 26 v to 50 v 5.6 w transfer ratio k k = v out / v in , i out = 0 a 1/8 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 20 a output current (peak) i out_pk t peak < 10 ms, i out_avg 20 a 30 a efficiency (ambient) h amb v in = 48 v, i out = 20 a 91.0 92.9 % v in = 26 v to 55 v, i out = 20 a 89.5 output resistance (cold) r out_cold t c = -40c, i out = 20 a 5.0 8.2 13.0 m output resistance (ambient) r out_amb t c = 25c, i out = 20 a 7.0 10.8 15.0 m output resistance (hot) r out_hot t c = 100c, i out = 20 a 9.0 13.2 18.0 m switching frequency f sw 1.37 1.50 1.63 mhz output ripple frequency f sw_rp 2.74 3.00 3.26 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 6.0 mhrs vc internal resistor r vc-int 4.64 k current monitor: im ? the im pin provides a dc analog voltage proportional to the output current of the vtm. signal type state attribute symbol conditions / notes min typ max unit analog input steady im voltage (no load) v im_nl t c = 25oc, v in = 48 v, i out = 0 a 0.27 0.33 0.37 v im voltage (50%) v im_50% t c = 25oc, v in = 48 v, i out = 10 a 1.0 v im voltage (full load) v im_fl t c = 25oc, v in = 48 v, i out = 20 a 1.91 v im gain a im t c = 25oc, v in = 48 v, i out > 10 a 91 mv/a im resistance (external) r im_ext 2.5 m
vtm ? current multiplier rev 1.3 vicorpower.com page 15 of 31 07/2015 800 927.9474 mvtm36 series model specific electrical characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mvtm36bh090m010 a00 no load power dissipation p nl v in = 26 v to 50 v 5.2 w transfer ratio k k = v out / v in , i out = 0 a 1/4 v/v ouput voltage v out v out = v in ? k - i out ? r out v output current (average) i out_avg 10 a output current (peak) i out_pk t peak < 10 ms, i out_avg 10 a 15 a efficiency (ambient) h amb v in = 36 v, i out = 10 a 92.0 93.6 % v in = 26 v to 50 v, i out = 10 a 90.0 output resistance (cold) r out_cold t c = -40c, i out = 10 a 20.0 27.0 35.0 m output resistance (ambient) r out_amb t c = 25c, i out = 10 a 28.0 36.2 45.0 m output resistance (hot) r out_hot t c = 100c, i out = 10 a 35.0 44.4 55.0 m switching frequency f sw 1.60 1.75 1.90 mhz output ripple frequency f sw_rp 3.20 3.50 3.80 mhz mtbf mil-hdbk-217 plus parts count; 25c ground benign, stationary, indoors / computer profile 4.5 mhrs vc internal resistor r vc-int 2.05 k current monitor: im ? the im pin provides a dc analog voltage proportional to the output current of the vtm. signal type state attribute symbol conditions / notes min typ max unit analog input steady im voltage (no load) v im_nl t c = 25oc, v in = 48 v, i out = 0 a 0.28 0.35 0.42 v im voltage (50%) v im_50% t c = 25oc, v in = 48 v, i out = 5 a 0.90 v im voltage (full load) v im_fl t c = 25oc, v in = 48 v, i out = 10 a 1.68 v im gain a im t c = 25oc, v in = 48 v, i out > 5 a 156 mv/a im resistance (external) r im_ext 2.5 m
vtm ? current multiplier rev 1.3 vicorpower.com page 16 of 31 07/2015 800 927.9474 mvtm36 series signal characteristics specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. vtm control: vc ? used to wake up powertrain circuit. ? a minimum of 12 v must be applied indefinitely for v in 26 v to ensure normal operation. ? vc slew rate must be within range for a successful start. ?prm ? vc can be used as valid wake-up signal source. ? vc voltage may be continuously applied; there will be minimal vc current drawn when v in 26 v and vc 13. ? internal resistance used in adaptive loop compensation signal type state attribute symbol conditions / notes min typ max unit analog input steady external vc voltage v vc_ext required for startup, and operation below 26 v. 12 16.5 v vc current draw threshold v vc_th low vc current draw for vin >26 v 13 v vc current draw i vc vc = 13 v, v in = 0 v 150 ma vc = 13 v, v in > 26 v 0 vc = 16.5 v, v in > 26 v 0 start up vc slew rate dvc/dt required for proper startup 0.02 0.25 v/s vc inrush current i inr_vc vc = 16.5 v, dvc/dt = 0.25 v/s 750 ma transitional vc output turn-on delay t on v in pre-applied, pc floating, vc enable; c pc = 0 f, c out = 4000 f 500 s vc to pc delay t vc_pc vc = 12 v to pc high, v in = 0 v, dvc/dt = 0.25 v/s 10 25 s primary control: pc ? the pc pin enables and disables the vtm. when held below 2 v, the vtm will be disabled. ? pc pin outputs 5 v during normal operation. pc pin is equal to 2.5 v during fault mode given vin 26 v and vc 12 v. ? after successful start-up and under no fault condition, pc can be used as a 5 v regulated voltage source with a 2 ma m aximum current. ? module will shutdown when pulled low with an impedance less than 400 ? . ? in an array of vtms, connect pc pin to synchronize startup. ? pc pin cannot sink current and will not disable other modules during fault mode. signal type state attribute symbol conditions / notes min typ max unit analog input steady pc voltage v pc 4.7 5.0 5.3 v pc source current i pc_op 2 ma pc resistance (internal) r pc_int internal pull down resistor 50 150 400 k start up pc source current i pc_en 50 100 300 a pc capacitance (internal) c pc_int 50 pf pc resistance (external) r pc_ext 60 k digital input / output enable pc voltage (enable) v pc_en 2 2.5 3 v disable pc voltage (disable) v pc_dis 2 v pc pull down current i pc_pd 5.1 ma transitional pc disable time t pc_dis_t 4 s pc fault response time t fr_pc from fault to pc = 2 v 100 s
vtm ? current multiplier rev 1.3 vicorpower.com page 17 of 31 07/2015 800 927.9474 mvtm36 series signal characteristics (cont.) specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. temperature monitor: tm ? the tm pin monitors the internal temperature of the vtm controller ic within an accuracy of 5c. ? can be used as a "power good" flag to verify that the vtm is operating. ? the tm pin has a room temperature setpoint of 3 v (@27c) and approximate gain of 10 mv/ c. signal type state attribute symbol conditions / notes min typ max unit analog output steady tm voltage v tm_amb t j controller = 27c 2.95 3.00 3.05 v tm source current i tm 100 a tm gain a tm 10 mv/c digital output (fault flag) disable tm voltage v tm_dis 0 v transitional tm resistance (internal) r tm_int internal pull down resistor 25 40 50 k tm capacitance (external) c tm_ext 50 pf tm fault response time t fr_tm from fault to tm = 1.5 v 10 s
vtm ? current multiplier rev 1.3 vicorpower.com page 18 of 31 07/2015 800 927.9474 mvtm36 series timing diagram 12 7 v in 1. initiated v c pulse 2. controller start 3. v in ramp up 4. v in = v ovlo 5. v in ramp down no v c pulse 6. overcurrent 7. start up on short circuit 8. pc driven low v out pc 3 v vc nl 5 v v ovlo tm v tm-amb c notes: C timing and voltage is not to scale C error pulse width is load dependent a: vc slew rate (dvc/dt) b: minimum vc pulse rate c: t ovlo d: t ocp e: output turn on delay (t on ) f: pc disable time (t pc_dis_t ) g: vc to pc delay (t vc_pc ) d i ssp i out i ocp v vc-ext 3 45 6 a b 8 g e f 26 v
vtm ? current multiplier rev 1.3 vicorpower.com page 19 of 31 07/2015 800 927.9474 mvtm36 series general characteristics specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit mechanical (full vic) length l 32.25 / [1.270] 32.5 / [1.280] 32.75 / [1.289] mm/[in] width w 21.75 / [0.856] 22.0 / [0.866] 22.25 / [0.876] mm/[in] height h 6.48 / [0.255] 6.73 / [0.265] 6.98 / [0.275] mm/[in] volume vol no heat sink 4.81 / [0.294] cm 3 /[in 3 ] weight w 15.0 / [0.53] g/[oz] (half vic) length l 21.7 / [0.85] 22.0 / [0.87] 22.3 / [0.88] mm/[in] width w 16.4 / [0.64] 16.5 / [0.65] 16.6 / [0.66] mm/[in] height h 6.48 / [0.255] 6.73 / [0.265] 6.98 / [0.275] mm/[in] volume vol no heat sink 2.44 / [0.150] cm 3 /[in 3 ] weight w 8.0 / [0.28] g/[oz] lead finish nickel 0.51 2.03 m palladium 0.02 0.15 gold 0.003 0.051 thermal operating temperature t j -55 125 c thermal resistance (full vic) jc isothermal heat sink and isothermal internal pcb 1 c/w thermal resistance (half vic) jc isothermal heat sink and isothermal internal pcb 2.2 c/w assembly storage temperature t st -65 125 c esd withstand esd hbm human body model component level ansi/esda/jedec js-001-2012, class 1c 1000 to <2000 v 1000 v dc esd cdm field induced change device model jesd22-c101e, class ii 200 to <500 v 200
vtm ? current multiplier rev 1.3 vicorpower.com page 20 of 31 07/2015 800 927.9474 mvtm36 series general characteristics cont. specifications apply over all line and load conditions, unless otherwise noted; boldface specifications apply over the temperat ure range of -55c < t j < 125c (t-grade); all other specifications are at t j = 25oc unless otherwise noted. attribute symbol conditions / notes min ty p max unit soldering peak temperature during reflow msl 4 (datecode 1528 and later) 245 c peak time above 217c 60 90 s peak heating rate during reflow 1.5 3 c/s peak cooling rate post reflow 1.5 6 c/s safety isolation voltage (hipot) v hipot 2250 v dc isolation resistance r in_out 10 m agency approvals / standards ctuvus curus ce marked for low voltage directive and rohs recast directive, as applicable
vtm ? current multiplier rev 1.3 vicorpower.com page 21 of 31 07/2015 800 927.9474 mvtm36 series using the control signals vc, pc, tm, im the vtm control (vc) pin is an input pin which powers the internal vcc circuitry when within the speci?ed voltage range of 12 v to 16.5 v. this voltage is required in order for the vtm module to start, and must be applied as long as the input is below 26 v. in order to ensure a proper start, the slew rate of the applied voltage must be within the speci?ed range. some additional notes on the using the vc pin: n in most applications, the vtm module will be powered by an upstream prm? which provides a 10 ms vc pulse during startup. in these applications the vc pins of the prm and vtm should be tied together. n the vc voltage can be applied inde?nitely allowing for continuous operation down to 0 v in . n the fault response of the vtm module is latching. a positive edge on vc is required in order to restart the unit. if vc is continuously applied the pc pin may be toggled to restart the module. primary control (pc) pin can be used to accomplish the following functions: n delayed start: upon the application of vc, the pc pin will source a constant 100 a current to the internal rc network. adding an external capacitor will allow further delay in reaching the 2.5 v threshold for module start. n auxiliary voltage source: once enabled in regular operational conditions (no fault), each vtm pc provides a regulated 5 v, 2 ma voltage source. n output disable: pc pin can be actively pulled down in order to disable the module. pull down impedance shall be lower than 400 . n fault detection ?ag: the pc 5 v voltage source is internally turned off as soon as a fault is detected. it is important to notice that pc doesnt have current sink capability. therefore, in an array, pc line will not be capable of disabling neighboring modules if a fault is detected. n fault reset: pc may be toggled to restart the unit if vc is continuously applied. temperature monitor (tm) pin provides a voltage proportional to the absolute temperature of the converter control ic. it can be used to accomplish the following functions: n monitor the control ic temperature: the temperature in kelvin is equal to the voltage on the tm pin scaled by 100. (i.e. 3.0 v = 300 k = 27oc). if a heat sink is applied, tm can be used to thermally protect the system. n fault detection ?ag: the tm voltage source is internally turned off as soon as a fault is detected. for system monitoring purposes (microcontroller interface) faults are detected on falling edges of tm signal. current monitor (im) (half chip models only) pin provides a voltage proportional to the output current of the vtm module. the nominal voltage will vary between v im_nl to v im_fl over the output current range of the module. the accuracy of the im pin will be within 25% under all line and temperature conditions between 50% and 100% load. startup behavior depending on the sequencing of the vc with respect to the input voltage, the behavior during startup will vary as follows: n normal operation (vc applied prior to vin): in this case the controller is active prior to ramping the input. when the input voltage is applied, the vtm output voltage will track the input. the inrush current is determined by the input voltage rate of rise and output capacitance. if the vc voltage is removed prior to the input reaching 26 v, the vtm module may shut down. n stand alone operation (vc applied after vin): in this case the module output will begin to rise upon the application of the vc voltage. a soft-start circuit may vary the ouput rate of rise in order to limit the inrush current to its maximum level. when starting into high capacitance, or a short, the output current will be limited for a maximum of 900 sec. after this period, the adaptive soft start circuit will time out and the module may shut down. no restart will be attempted until vc is re-applied, or pc is toggled. to ensure a successful start in this mode of operation, additional capacitance on the output of the vtm should be kept to a minimum. thermal considerations vi chip? products are multi-chip modules whose temperature distribution varies greatly for each part number as well as with the input / output conditions, thermal management and environmental conditions. maintaining the top of the vtm case to less than 100oc will keep all junctions within the vi chip below 125oc for most applications. the percent of total heat dissipated through the top surface versus through the j-lead is entirely dependent on the particular mechanical and thermal environment. the heat dissipated through the top surface is typically 60%. the heat dissipated through the j-lead onto the pcb board surface is typically 40%. use 100% top surface dissipation when designing for a conservative cooling solution. it is not recommended to use a vi chip module for an extended period of time at full load without proper heat sinking
vtm ? current multiplier rev 1.3 vicorpower.com page 22 of 31 07/2015 800 927.9474 mvtm36 series sine amplitude converter? point of load conversion the sine amplitude converter (sac?) uses a high frequency resonant tank to move energy from input to output. the resonant lc tank, operated at high frequency, is amplitude modulated as function of input voltage and output current. a small amount of capacitance embedded in the input and output stages of the module is sufficient for full functionality and is key to achieving power density. a typical sac can be simpli?ed into the model above. at no load: v out = v in ? k (1) k represents the turns ratio of the sac. rearranging eq (1): k= v out (2) v in in the presence of load, vout is represented by: v out = v in ? k C i out ? r out (3) and iout is represented by: i out =i in C i q (4) k r out represents the impedance of the sac, and is a function of the r dson of the input and output mosfets and the winding resistance of the power transformer. iq represents the quiescent current of the sac control and gate drive circuitry. the use of dc voltage transformation provides additional interesting attributes. assuming for the moment that r out = 0 and i q = 0 a, eq. (3) now becomes eq. (1) and is essentially load independent. a resistor r is now placed in series with v in as shown in figure 2. the relationship between v in and v out becomes: v out = (v in C i in ? r) ? k (5) substituting the simpli?ed version of eq. (4) (i q is assumed = 0 a) into eq. (5) yields: v out = v in ? k C i out ? r ? k 2 (6) this is similar in form to eq. (3), where r out is used to represent the characteristic impedance of the sac?. however, in this case a real r on the input side of the sac is effectively scaled by k 2 with respect to the output. assuming that r = 1 , the effective r as seen from the secondary side is 0.98 m, with k = 1/32 as shown in figure 2. a similar exercise should be performed with the additon of a capacitor, or shunt impedance, at the input to the sac. a switch in series with v in is added to the circuit. this is depicted in figure 3. + + v out c out v in v?i k + + c in i out r c out i q r out r c in figure 1 ? vi chip ? module ac model (mvtm48eh040m025a00 shown) 0.057 a 1/12 ? i out 1/12 ? v in 6.2 m r cin 6.3 m 150 ph 350 m r cout 330 68 f l out = 600 ph 900 nf i q l in = 1.7 nh i out r out v in v out c out c in r sac k = 1/32 vin vout + ? figure 2 ? k = 1/32 sine amplitude converter? with series input resistor
vtm ? current multiplier rev 1.3 vicorpower.com page 23 of 31 07/2015 800 927.9474 mvtm36 series a change in v in with the switch closed would result in a change in capacitor current according to the following equation: i c (t) = c dvin (7) dt assume that with the capacitor charged to v in , the switch is opened and the capacitor is discharged through the idealized sac. in this case, i c =i out ? k (8) substituting eq. (1) and (8) into eq. (7) reveals: i out = c?dv out (9) k 2 dt writing the equation in terms of the output has yielded a k 2 scaling factor for c, this time in the denominator of the equation. for a k factor less than unity, this results in an effectively larger capacitance on the output when expressed in terms of the input. with a k = 1/32 as shown in figure 3, c = 1 f would effectively appear as c = 1024 f when viewed from the output. low impedance is a key requirement for powering a high-current, low-voltage load efficiently. a switching regulation stage should have minimal impedance, while simultaneously providing appropriate ?ltering for any switched current. the use of a sac between the regulation stage and the point of load provides a dual bene?t, scaling down series impedance leading back to the source and scaling up shunt capacitance (or energy storage) as a function of its k factor squared. however, these bene?ts are not useful if the series impedance of the sac is too high. the impedance of the sac must be low well beyond the crossover frequency of the system. a solution for keeping the impedance of the sac low involves switching at a high frequency. this enables magnetic components to be small since magnetizing currents remain low. small magnetics mean small path lengths for turns. use of low loss core material at high frequencies reduces core losses as well. the two main terms of power loss in the vtm module are: n no load power dissipation (pnl): de?ned as the power used to power up the module with an enabled power train at no load. n resistive loss (r out ): refers to the power loss across the vtm current multiplier modeled as pure resistive impedance. p dissipated = p nl + p rout (10) therefore, p out = p in C p dissipated = p in C p nl C p rout (11) the above relations can be combined to calculate the overall module efficiency: h = p out =p in C p nl C p rout (12) p in p in = v in ? i in C p nl C (i out ) 2 ? r out v in ? i in = 1 C p nl + (i out )2 ? r out v in ? i in input and output filter design a major advantage of a sac? system versus a conventional pwm converter is that the former does not require large functional ?lters. the resonant lc tank, operated at extreme high frequency, is amplitude modulated as a function of input voltage and output current and efficiently transfers charge through the isolation transformer. a small amount of capacitance embedded in the input and output stages of the module is sufficient for full functionality and is key to achieving high power density. this paradigm shift requires system design to carefully evaluate external ?lters in order to: 1. guarantee low source impedance. to take full advantage of the vtm module dynamic response, the impedance presented to its input terminals must be low from dc to approximately 5 mhz. input capacitance may be added to improve transient performance or compensate for high source impedance. 2. further reduce input and/or output voltage ripple without sacri?cing dynamic response. given the wide bandwidth of the vtm module, the source response is generally the limiting factor in the overall system response. anomalies in the response of the source will appear at the output of the module multiplied by its k factor. 3. protect the module from overvoltage transients imposed by the system that would exceed maximum ratings and cause failures. the vi chip? module input/output voltage ranges must not be exceeded. an internal overvoltage lockout function prevents operation outside of the normal operating input range. even during this condition, the powertrain is exposed to the applied voltage and power mosfets must withstand it. () c s sac k = 1/32 vin vout + ? figure 3 ? sine amplitude converter? with input capacitor
vtm ? current multiplier rev 1.3 vicorpower.com page 24 of 31 07/2015 800 927.9474 mvtm36 series capacitive filtering considerations for a sine amplitude converter it is important to consider the impact of adding input and output capacitance to a sine amplitude converter? on the system as a whole. both the capacitance value, and the effective impedance of the capacitor must be considered. a sine amplitude converter has a dc r out value which has already been discussed in the previous section. the ac r out of the sac contains several terms: n resonant tank impedance n input lead inductance and internal capacitance n output lead inductance and internal capacitance the values of these terms are shown in the behavioral model in the prior section. it is important to note on which side of the transformer these impedances appear and how they re?ect across the transformer given the k factor. the overall ac impedance varies from model to model but for most models it is dominated by dc rout value from dc to beyond 500 khz. any capacitors placed at the output of the vtm module re?ect back to the input of the module by the square of the k factor (eq. 9) with the impedance of the module appearing in series. it is very important to keep this in mind when using a prm? regulator to power the vtm. most prm regulators have a limit on the maximum amount of capacitance that can be applied to the output. this capacitance includes both the regulator output capacitance and the current multiplier output capacitance re?ected back to the input. in prm regulator remote sense applications, it is important to consider the re?ected value of vtm current multiplier output capacitance when designing and compensating the prm regulator control loop. capacitance placed at the input of the vtm module appear to the load re?ected by the k factor, with the impedance of the vtm module in series. in step-down vtm ratios, the effective capacitance is increased by the k factor. the effective esr of the capacitor is decreased by the square of the k factor, but the impedance of the vtm module appears in series. still, in most step-down vtm modules an electrolytic capacitor placed at the input of the module will have a lower effective impedance compared to an electrolytic capacitor placed at the output. this is important to consider when placing capacitors at the output of the current multiplier. even though the capacitor may be placed at the output, the majority of the ac current will be sourced from the lower impedance, which in most cases will be the vtm current multiplier. this should be studied carefully in any system design using a vtm current multiplier. in most cases, it should be clear that electrolytic output capacitors are not necessary to design a stable, well-bypassed system. current sharing the sac? topology bases its performance on efficient transfer of energy through a transformer without the need of closed loop control. for this reason, the transfer characteristic can be approximated by an ideal transformer with some resistive drop and positive temperature coefficient. this type of characteristic is close to the impedance characteristic of a dc power distribution system, both in behavior (ac dynamic) and absolute value (dc dynamic). when connected in an array with the same k factor, the vtm module will inherently share the load current with parallel units, according to the equivalent impedance divider that the system implements from the power source to the point of load. some general recommendations to achieve matched array impedances: n dedicate common copper planes within the pcb to deliver and return the current to the modules. n provide the pcb layout as symmetric as possible. n apply same input / output ?lters (if present) to each unit. for further details see an:016 using bcm? bus converters in high power arrays. fuse selection in order to provide ?exibility in con?guring power systems vi chip? products are not internally fused. input line fusing of vi chip products is recommended at system level to provide thermal protection in case of catastrophic failure. the fuse shall be selected by closely matching system requirements with the following characteristics: n current rating (usually greater than maximum vtm module current) n maximum voltage rating (usually greater than the maximum possible input voltage) n ambient temperature n nominal melting i 2 t reverse operation the mvtm is capable of reverse operation. if a voltage is present at the output which satis?es the condition v out > v in ? k at the time the vc voltage is applied, or after the unit has started, then energy will be transferred from secondary to primary. the input to output ratio will be maintained. the mvtm will continue to operate in reverse as long as the input and output are within the speci?ed limits. the mvtm has not been quali?ed for continuous operation (>10 ms) in the reverse direction. v in v out + C dc z in_eq1 z in_eq2 z out_eq1 z out_eq2 load vtm 1 r o_1 vtm 2 r o_2 vtm n r o_n z out_eqn z in_eqn figure 4 ? vtm module array
vtm ? current multiplier rev 1.3 vicorpower.com page 25 of 31 07/2015 800 927.9474 mvtm36 series product outline & recommended land pattern; full vic smd, 18 pin
vtm ? current multiplier rev 1.3 vicorpower.com page 26 of 31 07/2015 800 927.9474 mvtm36 series product outline & recommended land pattern; full vic th, 60 pin
vtm ? current multiplier rev 1.3 vicorpower.com page 27 of 31 07/2015 800 927.9474 mvtm36 series recommended heat sink push pin location; full notes: 1. maintain 3.50 (0.138) dia. keep-out zone free of copper, all pcb layers. 2. (a) minimum recommended pitch is 39.50 (1.555). this provides 7.00 (0.275) component edge-to-edge spacing, and 0.50 (0.020) clearance between vicor heat sinks. (b) minimum recommended pitch is 41.00 (1.614). this provides 8.50 (0.334) component edge-to-edge spacing, and 2.00 (0.079) clearance between vicor heat sinks. 3. vi chip module land pattern shown for reference only; actual land pattern may differ. dimensions from edges of land pattern to push?in holes will be the same for all full-size vi chip products. 4. rohs compliant per cst?001 latest revision. (no grounding clips) (with grounding clips) 5. unless otherwise specified: dimensions are mm (inches) tolerances are: x.x (x.xx) = ?.3 (0.01) x.xx (x.xxx) = ?.13 (0.005) 6. plated through holes for grounding clips (33855) shown for reference, heat sink orientation and device pitch will dictate final grounding solution.
vtm ? current multiplier rev 1.3 vicorpower.com page 28 of 31 07/2015 800 927.9474 mvtm36 series mechanical drawing; half vic smt, 12 pin
vtm ? current multiplier rev 1.3 vicorpower.com page 29 of 31 07/2015 800 927.9474 mvtm36 series recommended heat sink push pin location; half (no grounding clips) (with grounding clips) notes: 1. maintain 3.50 (0.138) dia. keep-out zone free of copper, all pcb layers. 2. (a) minimum recommended pitch is 24.00 (0.945) this provides 7.50 (0.295) component edge?o?dge spacing, and 0.50 (0.020) clearance between vicor heat sinks. (b) minimum recommended pitch is 25.50 (1.004). this provides 9.00 (0.354) component edge?o?dge spacing, and 2.00 (0.079) clearance between vicor heat sinks. 3. vi chip module land pattern shown for reference only, actual land pattern may differ. dimensions from edges of land pattern to push?in holes will be the same for all half size v? chip products. 4. rohs compliant per cst?001 latest revision. 5. unless otherwise specified: dimensions are mm (inches) tolerances are: x.x (x.xx) = ?.13 (0.01) x.xx (x.xxx) = ?.13 (0.005) 6. plated through holes for grounding clips (33855) shown for reference. heat sink orientation and device pitch will dictate final grounding solution.
vtm ? current multiplier rev 1.3 vicorpower.com page 30 of 31 07/2015 800 927.9474 mvtm36 series revision history revision date description page number(s) 1.0 3/2014 initial release n/a 1.1 11/25/2014 typ value of vc internal resistor 12 1.2 1/07/2015 updated 3 v part to b version 5 1.3 07/??/15 what would you like to say here? 19 & 20
vtm ? current multiplier rev 1.3 vicorpower.com page 31 of 31 07/2015 800 927.9474 mvtm36 series vicor?s comprehensive line of power solutions includes high density ac-dc and dc-dc modules and accessory components, fully configurable ac-dc and dc-dc power supplies, and complete custom power systems. information furnished by vicor is believed to be accurate and reliable. however, no responsibility is assumed by vicor for its use. vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. information published by vicor h as been checked and is believed to be accurate at the time it was printed; however, vicor assumes no responsibility for inaccuracies. testing and other quality controls are used to the extent vicor deems necessary to support vicor?s product warranty. except where mandated by government requirements , testing of all parameters of each product is not necessarily performed. specifications are subject to change without notice. vicor?s standard terms and conditions all sales are subject to vicor?s standard terms and conditions of sale, which are available on vicor?s webpage or upon request. product warranty in vicor?s standard terms and conditions of sale, vicor warrants that its products are free from non-conformity to its standard specifications (the ?express limited warranty?). this warranty is extended only to the original buyer for the period expiring two (2) years after t he date of shipment and is not transferable. unless otherwise expressly stated in a written sales agreement signed by a duly authorized vicor signatory, vicor disclaims all representations, liabilities, and warranties of any kind (whether arising by implication or by operation of law) with respect to the products, including, without limitation, any warranties or representations as to merchantability, fitness for particular purpose, infringement of any patent, copyright, or other intellectual property right, or any other matter. this warranty does not extend to products subjected to misuse, accident, or improper application, maintenance, or storage. vico r shall not be liable for collateral or consequential damage. vicor disclaims any and all liability arising out of the application or use of any pro duct or circuit and assumes no liability for applications assistance or buyer product design. buyers are responsible for their products and applications us ing vicor products and components. prior to using or distributing any products that include vicor components, buyers should provide adequate design, testing and operating safeguards. vicor will repair or replace defective products in accordance with its own best judgment. for service under this warranty, the buyer must contact vicor to obtain a return material authorization (rma) number and shipping instructions. products returned without prior author ization will be returned to the buyer. the buyer will pay all charges incurred in returning the product to the factory. vicor will pay all re shipment charges if the product was defective within the terms of this warranty. life support policy vicor?s products are not authorized for use as critical components in life support devices or systems without the express prior written approval of the chief executive officer and general counsel of vicor corporation. as used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and wh ose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a s ignificant injury to the user. a critical component is any component in a life support device or system whose failure to perform can be reasonably expec ted to cause the failure of the life support device or system or to affect its safety or effectiveness. per vicor terms and conditions of sale, the user of vicor products and components in life support applications assumes all risks of such use and indemnifies vicor against all liability and damag es. intellectual property notice vicor and its subsidiaries own intellectual property (including issued u.s. and foreign patents and pending patent applications ) relating to the products described in this data sheet. no license, whether express, implied, or arising by estoppel or otherwise, to any intel lectual property rights is granted by this document. interested parties should contact vicor's intellectual property department. the products described on this data sheet are protected by the following u.s. patents numbers: 5,945,130; 6,403,009; 6,710,257; 6,911,848; 6,930,893; 6,934,166; 6,940,013; 6,969,909; 7,038,917; 7,145,186; 7,166,898; 7,187, 263; 7,202,646; 7,361,844; d496,906; d505,114; d506,438; d509,472; and for use under 6,975,098 and 6,984,965. vicor corporation 25 frontage road andover, ma, usa 01810 tel: 800-735-6200 fax: 978-475-6715 email customer service: custserv@vicorpower.com technical support: apps@vicorpower.com

▲Up To Search▲

Price & Availability of MVTM36BH030M025A00

	To Download MVTM36BH030M025A00 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .